Power632 PC1555 Instruction Manual Security System DSC POWERSERIES PC1616 User Manual. + 3 original “memory card roms”(sound-libraries-series).dsc-02 voice of tokyo with instruction manual, original 9v dc power supply, vocoder microphone. Dsc Power Series 433 Instruction Manual Read/Download.
Dsc Pc1616 Programming
Download Operation & user’s manual of DSC PowerSeries PC1616 Control Panel, Network Router for Free or View it Online on All-Guides.com. This version of DSC PowerSeries PC1616 Manual compatible with such list of devices, as: PowerSeries PC1616, PowerSeries PC1832, PC1616; PC1832; PC1864, PowerSeries PC1864
Brand: DSC
Category: Control Panel , Network Router , Other , Security System
Type: Operation & user’s manual
Model: DSC PowerSeries PC1616 , DSC PowerSeries PC1832 , DSC PC1616; PC1832; PC1864 , DSC PowerSeries PC1864
Pages: 28 (1.81 Mb)
Sensor / Zone Information
SensorProtected AreaSensor TypeSensorProtected AreaSensor Type
0234
0436
0638
0840
1042
1244
1446
1648
1850
2052
2254
2456
2658
2860
3062
3264
Related Products for DSC PowerSeries PC1616Related Manuals for DSC PowerSeries PC1616DSC PowerSeries PC1616: Frequently viewed Manuals
Advertising
Hardware Installation (Cont.)
4. AUX Power Wiring
The control panel can provide a maximum of 700mA of current for modules, powered detectors, relays, LED’s etc.… If the total current
required exceeds 700mA an additional power supply is required (e.g.,PC5200, PC5204). See list below.
NOTE: Min/max operating voltages for devices, sensors and modules is 9.5V
DC
- 14V
DC
![]()
Refer to the list of Compatible Devices on the first page for the current draw of individual devices
5. PGM Wiring
PGMs switch to ground when activated by control panel.
Connect the positive side of the device to be activated to the AUX+ Terminal. Connect the negative terminal to the PGM. current output is as follows •
PGM 1, 3, 4 .......... 50mA
•
PGM 2 ............. 300mA
For currents levels greater than 300mA a relay is required.
PGM2 can also be used for 2-wire smoke detectors.
NOTE: Use SEOL resistors on Fire Zones ONLY.
PGM 1, LED Output with current limiting resistor and Optional Relay
driver output
2-wire Smoke Detectors Initiating Circuit
•
Style B (Class B), Supervised, Power Limited
•
Compatibility Identifier ............................ PC18-1
•
DC Output Voltage........................... 9.8-13.8 VDC
•
Detector Load ............................... 2 mA (MAX)
Dsc Power 1616 Installation Manual
•
Single-end-of-line (SEOL) Resistor ................... 2200
Ω
•
Loop Resistance..............................24
Ω (MAX)
•
Standby Impedance......................... 1020
Sony vegas pro serial code. Ω (ΝΟΜ)
•
Alarm Impedance ............................570
Ω (MAX)
•
Alarm Current .............................. 89 mA (MAX)
Compatibility ID For FSA-210B Series is: FS200
4-wire Smoke Detectors
6. Telephone Line Wiring
Wire the telephone connection terminals (TIP, Ring, T-1, R-1) to an
RJ-31x Connector as indicated.
For connection of multiple devices to the telephone line, wire in the
sequence indicated. Telephone format is programmed in section [350]. Telephone Call Directions are programmed in section [351]-[376].
7. Ground
8. Battery
9. AC Wiring
Ground Installation
A sealed, rechargeable, lead
acid battery or gel type battery is required to meet UL require- ments for power standby times. NOTE: UL Residential/Commer- cial Burglary installations require 4Hrs Power Standby time. NOTE: UL/ULCResidential Fire & Home Care installations require 24 Hr power standby. ULC Commercial Burglary and Fire monitoring installations require 24 Hr power standby.
Standby Battery Guide
Battery Charging Current: 400 mA
Batt
Standby
Size
4Hr
24Hr
-------------------------------------------------
4Ahr
700mA
----
7Ahr
700mA
180mA
14Ahr
700mA
470mA
NOTE:
Replace batteries every 3-5 years.
Battery capacity will deteriorate with age and number of charge/discharge cycles
AC Wiring
UL Listed Installations
Primary: 120VAC/60Hz./0.33A Secondary: 16.5VAC/40VA DSCPTD 1640 Plug-in, Class 2 Transformer. Dsc Pc1616 Installation Manual Pdf
NOTE: Do not connect trans-
former to a receptacle controlled by a switch. (UL Listed Installations Only)
RM-1/RM-2 POWER LOOP
SUPERVISORY RELAY
T-1
Dsc Pc1616 Installation Manual Download
R-1
TIP
RING
RJ-31X
Tighten nut to break paint and make
good connection to the cabinet
Dsc Pc1832 Install Manual
Advertising
Dsc Pc1616
This manual is related to the following products:
Popular Brands
Popular manuals
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |